Best thickness for a lithophane, and the print settings that go with it
The best lithophane thickness is 0.8 mm at the brightest points and 3.0 mm at the darkest, printed in white PLA at 0.12 mm layers, 100% infill, standing upright. Change the two thickness numbers below and watch the backlit preview: that is how your light will look.
Warming up the preview…
Try a sample:or drop / paste a photo. It stays on your device.
Fine-tune
Free: no account, no watermark. A closed solid in millimetres for any slicer.
Make it a gift $9.99
A printable card with your lithophane glowing on the front and your message inside — tuck it in the box with the print.
Print settings
- Filament white PLA (not “natural” or glossy)
- Layer height 0.12 mm (0.1–0.16)
- Infill 100%, or 99% with wall count ≥ 5
- Orientation standing upright, as the file is saved
- Speed 40–60 mm/s outer walls; brim on for tall panels
How thickness turns into light
White PLA scatters light, so each extra millimetre lets through roughly a quarter as much. These swatches use the same model as the 3D preview, lit by a warm LED:
Below 0.6 mm the wall is fragile and the nozzle may leave gaps that shine as bright dots. Above 3.5 mm extra thickness only adds print time: the light is already gone.
Print settings that work
| Setting | Use | Why |
|---|---|---|
| Thinnest / thickest | 0.8 / 3.0 mm | ~30:1 contrast with a warm LED |
| Layer height | 0.12 mm | Vertical detail of the picture |
| Infill | 100% | No grid shadows in the light |
| Orientation | Upright | Detail drawn by the nozzle, not layer steps |
| Outer wall speed | 40–60 mm/s | Less wobble on tall thin walls |
| Nozzle | 0.4 mm (0.25 for tiny prints) | Finer nozzle → try HD resolution |
| Filament | White PLA, matte | Even scattering, neutral tone |
| Light | Warm white LED, 2700–3000 K | Flattering skin tones; never a flame |
When to change the defaults
- Bright light box or daylight window: raise the thickest wall to 3.2–3.5 mm so shadows stay dark.
- Weak LED tea light: lower it to 2.4–2.6 mm.
- Big panels (over 150 mm): add 1 mm of border and keep the thinnest at 0.8 mm or more so the panel stays stiff.
- Resin printers: resin is more translucent; try 0.5 / 2.5 mm.
Questions people ask
What is the best thickness for a lithophane?
0.8 mm for the brightest parts and 3.0 mm for the darkest is the best all-round range for white PLA and a 0.4 mm nozzle. It gives about 30:1 contrast with an ordinary warm LED.
What layer height should I use for lithophanes?
0.12 mm is a good default; anything from 0.08 to 0.16 mm works. Because lithophanes print upright, layer height sets the vertical detail of the picture.
What infill should a lithophane have?
100% infill. Partial infill shows as a grid pattern when the light is on. If your slicer struggles, use 99% with 5 or more walls.
Should I print a lithophane flat or standing up?
Standing up. The picture detail is then drawn by the nozzle path instead of layer steps, and the light passes through solid walls. Add a brim for panels taller than about 120 mm.
Which filament is best for lithophanes?
Plain white PLA (not “natural”, translucent or silk). PETG works but is glossier; dark or coloured filaments block too much light.
Why does my lithophane look too dark?
The thickest wall is too thick for your light, or the filament is too opaque. Lower the thickest setting to 2.5–2.8 mm or use a brighter LED.